We are purchasing a new refrigerator to use the “Cash for Clunkers for Appliances” program.

Brand New refrigerator we would like posseses an ice manufacturer, which obviously (right?) is certainly going to need a water hookup which our present suck-ass Magic Chef doesn’t. Just how much of an issue (in work and expense; we are in Brooklyn, NY) could it be to include a brand new hookup? It really is close to our drain, therefore the pipelines should there be right.

If, for reasons uknown, it is not practical to have the job done, can there be any explanation we couldn’t simply connect within the refrigerator sans-ice manufacturer, and connect it later on?

you need to be able to install the manual on the web. Observe how the directions read.

We suspect it’s going to be since straightforward as placing a T on your own cool water line and operating a plastic that is small towards the straight straight straight back for the refrigerator. but. IANAP posted by HuronBob at 2:42 PM on February 11, 2010

Residence Depot offers a kit because of this. It is simply only a little needle thing that taps into the pipe that is existing. I believe it is a kit that is slightly different on for those who have copper or PVC.

Yeah, then drill a hole in the cabinet to run the line if the fridge is going in right next to the sink, I would use a saddle valve on the cold line to the sink. You ought to be able to perform all the work (aside from drilling the opening) with fundamental hand tools plus some sense that is common.

1) If you have not really bought yet, I would like to emphatically endorse purchasing a model because of the fridge from the base. It really is Hence very nice getting the meals you access most be appropriate up there in the front of one’s face.

2) setting up an ice manufacturer line must not be way too hard. My hubby recently changed ours out from a copper line to at least one of those lines that appears like a fuel pipe (bendy and much more durable because our copper line create a kink inside it and leaked). With respect to the types of line you utilize, you may need to make many, numerous batches of ice which you discard since you can “taste” the synthetic or long lasting line consists of. Maybe maybe maybe Not an issue, merely a pain you about that I thought I’d warn. posted by wwartorff at 3:26 PM on 11, 2010 february

“If, for reasons uknown, it is not practical to obtain the job done, can there be any reason we could not simply plug into the refrigerator sans-ice manufacturer, and connect it later on? “

No issue just exactly what therefore ever; just be sure you Ice Maker is within the off place so it doesn’t cycle all of the kind.

jon1270 writes ” For an ice manufacturer, a saddle valve must certanly be adequate.”

Saddle valves are virtually going to leak sooner or later later on; particularly under a sink where they’ve been afflicted by damage that is mechanical. Better is either a Compression Tee/Quick tee adaptor or a shut down valve with two ports whenever you can find the one that fits your water sink that is cold shutoff. Either may be set up in just a few wrenches and perchance a pipe cutter.

The ice maker kits that are install include either synthetic or copper tubing. The copper tubing is more high priced but less likely to want to be catastrophically damaged. Once you operate the line drill the gap into the case as near to the ground and wall surface as you are able to. Then make a sizable loop that is complete the tubing (roughly since big across because the width associated with refrigerator; 5-7′ of line) before connecting the conclusion regarding the tubing towards the water valve regarding the refrigerator. The cycle shall lay flat resistant to the wall surface behind the fridge and permit you to definitely pull the fridge right out of the wall surface without damaging the tubing. Make certain you utilize the clamp that is included with the kit to connect the tubing to your refrigerator near it really is valve therefore the valve does not get damaged.

Should your water contains appreciable sediment (search for mud within the base of the lavatory tank) along with your refrigerator additionally dispenses cold water then you definitely should install an inline sediment filter. Otherwise that muck ends up in the cold dish that chills water. posted by Mitheral at 3:44 PM on February 11, 2010 [2 favorites]

The very first thing you have to do is look beneath the sink and discover what sort of supply would go to the chilled water. In case it is a body that is valve versatile lines operating up, verify that the threads on top are standard half inch pipeline threads. In that case, you are able to unscrew water line into the sink lumen and install an easy tee over the valve, re-install the water line then install the kit-based line to your fridge. Of course you will have turned water off before unscrewing such a thing. Appropriate?

Simply simply simply Take a cellular phone picture of what is beneath the sink and show it into the plumbing “expert” in the home Depot or Lowes and s/he can explain to you all the goodies you need. As happens to be noted above, the most difficult part is drilling for the line through the case and that is actually no big deal. We elect to drill just a little bigger hole than is necessary therefore feeding the ice-maker line through is just a little easier. Additionally, drill this hole dating back feasible, therefore the line does not interfere because of the material you retain when you look at the case. published by Old Geezer at 4:40 PM on February 11, 2010